DETAIL KOLEKSI

Studi Laboratorium Pengaruh Penambahan Clay Terhadap Sifat Lumpur Pada Berbagai Temperatur


Oleh : Ridwan Pahlepi

Info Katalog

Nomor Panggil : 2162/TP/2013

Penerbit : FTKE - Usakti

Kota Terbit : Jakarta

Tahun Terbit : 2013

Pembimbing 1 : Bayu Satyawira

Subyek : Drilling Mud

Kata Kunci : the addition of clay, viscosity, plastic viscosity, yield point, gel strength, water loss, mud cake,


File Repositori
No. Nama File Ukuran (KB) Status
1. 2013_TA_TM_07107117_8.pdf 763.89
2. 2013_TA_TM_07107117_7.pdf 529.59
3. 2013_TA_TM_07107117_6.pdf 469.87
4. 2013_TA_TM_07107117_5.pdf 534.72
5. 2013_TA_TM_07107117_4.pdf 1121.03
6. 2013_TA_TM_07107117_3.pdf 739.62
7. 2013_TA_TM_07107117_2.pdf 416.59
8. 2013_TA_TM_07107117_1.pdf 2396.87

T Tujuan tugas akhir ini adalah untuk meneliti pengaruh penambahan clay terhadap sifat fisik lumpur KCl PHPA polimer pada berbagai temperature. Hal ini dapat mempengaruhi sifat – sifat rheologi lumpur tersebut dan bisa membuat lumpur tersebut menjadi tidak ideal untuk dilakukan penambahan clay. Penelitian yang dilakukan di laboratorium pemboran dan produksi Universitas Trisakti ini dilakukan dengan 1 lumpur tapi dengan kadar clay di Lumpur A1 (0 ppb), Lumpur A2 (2.5 Ppb), Lumpur A3 (5 Ppb), Lumpur A4 (7.5 Ppb), dan Lumpur A5 (10 Ppb). Percobaan ini dilakukan dengan berbagai temperatur yaitu 80°F, 120°F, 160°F, 200 °F, dan 240 °F. Pengaruh penambahan clay pada sistem lumpur berakibat naiknya nilai harga berat jenis, viskositas, plastic viscosity, yield point, gel strength, water loss, mud cake. Sedangkan nilai pH filtrate mengalami penurunan dan ditemukan peningkatan nilai MBT yang di sebabkan karena pengaruh kadar clay yang ada didalam system lumpur KCl PHPA polymer. Pengaruh temperatur terhadap penambahan clay pada sistem lumpur berakibat turunnya harga berat jenis, viskositas, plastic viscosity, yield point,gel strength,PH filtrate,chloride. Sedangkan water loss, mud cake berakibat turun. Dari hasil percobaan ini dapat disimpulkan bahwa lumpur A1 memenuhi spesifikasi lumpur yang diinginkan tetapi nilai water loss pada lumpur A1 memenuhi harga specifikasi <12,5 ml/30min, namun tidak memenuhi harga specifikasi pada temperature 2000 F dan 2400 F. Sedangkan untuk lumpur A2, A3, A4, dan A5 yang mengalami penambahan konsentrasi clay tidak memenuhi spesifikasi yang telah ditetapkan di laboratorium.

T The purpose of this thesis is to investigate the effect of clay on the physical properties of polymer PHPA mud KCl at various temperatures. This can affect the nature - rheological properties of the mud and the mud could make a less than ideal for the addition of clay. Research conducted in the laboratory of the University of Trisakti drilling and production is done with 1 mud but with the clay content in the Mud A1 (0 ppb), Mud A2 (2.5 ppb), Mud A3 (5 ppb), Mud D (7.5 ppb), and Mud E (10 ppb). The experiments carried out with various temperature is 80 ° F, 120 ° F, 160 ° F, 200 ° F, and 240 ° F. The effect of adding clay to mud system resulted in the increased value of the price density, viscosity, plastic viscosity, yield point, gel strength, water loss, mud cake. While the filtrate pH value decreased and found an increase in the value of MBT which is caused due to the influence of the clay content is in KCl PHPA polymer mud system. Influence of temperature on the addition of clay mud systems result in a decrease in the price of specific gravity, viscosity, plastic viscosity, yield point, gel strength, filtrate pH, chloride. While water loss, resulting mud cake down. From the experimental results it can be concluded that the sludge A1 sludge meets the desired specifications but the value of water loss in the mud A1 meet specifications prices <12.5 ml/30min, but does not meet specifications prices at temperatures of 200 0F and 240 0F. As for the mud A2, A3, A4, and A5 which has the addition of clay concentration does not meet the specifications established in the laboratory.

Bagaimana Anda menilai Koleksi ini ?